Having problems with your 1992 Chevrolet S-10 ?

My brake lights still dont work on my 96 S 10 Blazer. The fuse is good and i just relplaced the brake switch. Not sure where to look next ??? The wiring hasnt been ripped apart or damaged that i can see. The vehicle is in good shape I noticed they were not working when got done using my snowmobile trailer but im not sure if they did not work when i was using it. any suggestions would be great brent

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Did you also check the relays and fuses under the hood, or just the ones in the car as the ones under the hood control your brake lights too
Repair Help & Product Troubleshooting for 1992 Chevrolet S-10

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My brake lights still dont work on my 96 S 10 Blazer. The fuse is good and i just relplaced the brake switch. Not sure where to look next ??? The wiring hasnt been ripped apart or damaged that i can see. The vehicle is in good shape I noticed they were not working when got done using my snowmobile trailer but im not sure if they did not work when i was using it. any suggestions would be great brent


Did you also check the relays and fuses under the hood, or just the ones in the car as the ones under the hood control your brake lights too ... 1992 Chevrolet S-10

I have a 95 ford f-350 bought about two monthes ago. Today i jump in to run to the store and the brakes are spongy. I bleeded rear the abs then front and still the same thing. They work ok till the brake light comes on then they get spongy. The light comes on after braking then goes off after driving a 1/4 mile or so. Im at a lose. Think that its air but not sure how i got air in a closed system. I have done no work on it.


Replace your brake master cylinder. ... Ford F-350

My 87 ford rangers brake lights will not go out unless i unhook the turn signal switch. I thought it was the brake light switch but i unpluged it and they stayed on so i tested it and shows to be good so i thought maybe it was the turn signal switch so i found two used ones, one i know should be good the other not sure about, but got the same results out of all three switchs. Even tried pulling fuses and nothing else will kill them. NEED HELP! I would like to get it back on the road. What in the


You must have some wires shorted together somewhere ... 1987 Ford Ranger

Somerset Alternator I just bought a 1986 Buick Somerset used for $100, and I was told it needed a new alternator, So i picked on up at a junk yard took it to shucks and they told me it was in good working condition. So put it in. and now its not charging my Battery. I had my uncle take a look at it, and he is stumped at the moment too, I think it could be a fuse but Im not sure which one powers the Alternator, Anybody got any ideas why it wouldnt be charging? I know the Battery is good. Addition


I have a 1985 Buick Regal Somerset with similar problem. I solved issue by purchasing a high output alternator that would charge battery and power all accesories better. This helped along with changing the size of alternator pulley. If voltage output ... 1986 Buick Somerset

I have a 96 sebring convertible. I set the alarm off by opening the drivers door and then used the key in door to stop the alarm. I then tried to start but got nothing. I have locked and then unlocked doors and did not work. checked fuses, all good. unhooked batt and let sit 12 hours and still nothing. I have done this 3 times now. everything else works but will not turn over. Is there a sencor somewere? Help Please


Hello! I'm working on your problem................Guru..........Saailer ... 1996 Chrysler Sebring

1999 Pontiac Trans Am 5.7 Engine Automatic Transmission. Transmission went bad, only first, second and reverse worked , no third and no forth, already got a good used transmission, but I am not sure if I have to replace the torque converter as well.,is it nesessary to replace the torque converter or is it ok to put the same one it had before? Thank you..


It is a bad idea to use the one you had,a new one would be better,or new rebuilt,there will be trash,metal particles in the converter you will not want in this transmission.I think they are about 60 to 75 dollars,but worth the hassel of pulling it ba ... Pontiac Firebird

I have a 1992 Toyota Camry LE sedan. It has approx 197,000 on it. I bought it used 9 years ago and I love this car It is in great condition. My question is I want to keep it in good shape and am not sure what should be done, besides the basics(oil changes) I check the fluid. What other things should I do to keep the car running well. If I take it to mechanic i end up paying over $1000 for things that did not need fixing. As i said it is running well, yet is old and have not changed any fluids


I would have to see it to say for sure.Things like the timing belt and water pump should have been changed at every 80,000 mile point. Same goes for belts and coolant hoses.Ignition system parts and the fuel filter around 60,000 mile points. ... Toyota Camry

2004 Ford Explorer - While driving my battery light came on. The lights got dim and the power steering and brakes stopped working. My son thinks this only happens when he uses the cruise control but I'm not sure. what could this be?


Hello barbie1201. This could be a number of things, but let me mention a few things that I would do first.\015\012If you have recently changed the battery you need to make sure that the battery has the minimum cranking amps required for that ve ... Ford Explorer

While driving my 2004 Ford Explorer the battery light came on, the lights got dim and the power brakes and steering stopped working. My son thinks this only happens while using cruise control, but I'm not sure. He pulled over, shut off the truck anf restarted it and it was fine. What could this be?


This could be a sign of the charging system starting to fail. Have your alternator & battery checked for potential failure. ... 2004 Ford Explorer

All of the brake lights are out on my 2005 xterra. The tail lights still work, the reverse lights work, bulbs are good. I checked the brake light switch on the pedal and it is good, all fuses are good and plugs are all connected. I am not sure what the problem could be now. The auto parts store said that my vehicle doesn't have a brake relay and I cannot see that it has one so I am at a loss. Please help!


The brake light circuit is fairly basic:- 12V supply, stop sw, (optional relay), then stoplamps to ground.\015\012\015\012See for a free manual download:-\015\012 ... 2005 Nissan Xterra

1992 GMC K 1500?Here?s the scenario; Cruise control hasn?t worked in 8 years, just decided it would be nice to have and since the truck is in great condition and everything else worked on the truck, thought we?d fix the cruise control? What has been done so far; no code appear, new cruise control lever, new brake switch, remanufactured cruise control module, new vss? Fuses are good, brake lights working everything else including the wiring looks good? And still no cruise control? What other thin


Put a scanner on it and check data,and do an actuator test ,to see if it will work ... 2002 Chevrolet Blazer

Brake lights i have a 1998 ford explorer sport the brake lights are not working i have checked the bulbs and they are good the brake light above the hatch back works so i am not sure what to do?? Also i belive whatever is causing the lights not to work is also draining the battery i replaced it the next day it was dead again i can jump it off but it dies within a block. What do you suggest


Did you change the light bulb? sometimes you can not find whether it is out of order or not, you have to use a Om amp meter to make sure it is broken, anyway put a good new one there and see what’s happening. Usually there are many electronic r ... 1998 Ford Explorer

Brakes Locking My brake lights were not working. My husband checked the fuse and it was good. He then replaced the switch under the brake pedal. It seemed to work but not the brakes keep locking and the car is driving like the emergency brake is on. It seems to be ok when you first start driving and then happens in approx. 10 - 15 minutes. Could he have done something when he replaced the switch to make this happen?


Its possible he has the brake switch too tight or otherwise out of adjustment depending on the type of vehicle.If only one wheel is getting hot I would look at the brakes on that wheel. ... Cars & Trucks

THE HORN NO LONGER WORKS WHEN YOU HIT THE AIR BAG.THE HORN USED TO WORK TO EASLY WHEN YOU JUST LIGTHLY TOUCHED THE AIR BAG THEN THE HORN WOULD SOUND WHEN YOU TURNED THE WHEEL MY FATHER PUNCHED THE AIR BAG TO STOP THE HORN FROM SOUNDING NOW IT WILL NOT WORK AT ALL.I CHECKED THE FUSE,FUSE IS GOOD SOMEONE TOLD ME THAT THE HORN WORKS THREW THE AIR BAG (NEW DRIVER,S AIR BAG FROM GM IS ABOUT $800.00 FOR THE PART ONLY) WHEN FOR A USED ONE I ALSO GOT A NEW CLOCK SPRING INSTALLED ALL PARTS STILL NO HORN


The lights inside my dashboard not working, other then the fuses what should i be looking for?... (1998 buick skylark.)\015\012\015\012\015\012 thanks,,,, ... 1998 Buick Skylark

I have a 2002 kia sportage 4x4 5 speed manual. i drove it to work and drove home from work everything was working fine. the next morning i got in the car and pushed the clutch to start it and the pedal had no pressure at all. i started it in 1st gear and drove it with out the clutch and everything works fine. just no clutch pressure in pedal. is the brake master cylinder used for the clutch and the brakes? im thinking it might be the slave cylinder. i had someone push the clutch while i watched


... 2002 Kia Sportage

We have a 1990 Celica GTS hatchback w/ 5 FSE- 2.2 liter engine w/ 5 speed tranny. It also has A/C & antilock brakes. My wife was sitting in drive thru lane @ B. King & said she heard a pop & brake pedal went to the floor. She got home w. emergency brake & downshifting.(Good Girl) ----- Now the pedal is hard to push & pads feel like they're not putting enough pressure against the disks thus braking distance is not very good. ----- Took the master cylinder off & it is working fine.---- None of the


Sounds like brake booster not working especially if you have a hard brake pedal while engine is going(no power assistance) pop could have been diaphram in booster which is what the brake master cylinder bolts to.\015\012to check booster perform ... 1990 Toyota Celica

Replaced Master Cylinder and Brake Booster on 03 Bravada and pedal still drops all the way to the floor instead of stopping at half-way of pedal travel? No visible leaks in hydraulic system but it acts like it. Replaced new Master Cylinder with a second Master Cylinder just to verify that I got a good part but still had problem. Manual brakes work like normal when vacuum is removed from Brake Booster; no dropping to the floor. Brake pads and calipers on all 4 wheels look good and no leaks in bra


Did you replace the master cylinder and booster because of this? If so then did this problem follow any maintenance done on the brakes? Was there any leaks prior to the replaced parts?The pedal dropping to the floor with no leaks would point to ... 2002 Oldsmobile Bravada

I am trying to make sure my brake controller is properly wired. my brakes do not work automatically when I press the brake pedal,but do work when I manually use switch on brake controller.


Use a test light and find the wire that has power when you press the brake pedal. This is the wire that you need to tap into for you trailer brake controller. ... Dodge Ram Pickup 2500

Brake lite on console comes on/off. fluid levels look good. brakes get spongy go to floor, but pump them up and they work and light goes off.


If you don't see wetness around the brake lines (along the frame rail, at the back of the wheel, at the master cylinder), there is no reason to think that the fluid is low or leaking. Most likely is that your pads have worn down causing the calipers ... 1998 Jeep Wrangler

Periodically the clock resets itself when the car is restarted. This morning on the way to work the ABS and brake lights came on and braking was difficult. Then when I stopped for a light the ABS light and brake light came on again and the ABS kicked in. Then it was fine. Tonight when I got home, I tried to lock it with my remote. It wouldn't work, so I tried to lock using the lock button inside. No luck! Not only that the car won't start at all, no lights,no radio, can't shift. However, while I


This is a pinched wireloom problem the harness has a short in it possibly damaging a relay or, two.\015\012the best thing to do is: take your car to a certified auto electric shop: before it causes a fire; the cost will be well worth it and, s ... 2004 Chevrolet Malibu Maxx

I have a 96 chevy s-10 with a 2.2 liter 4cylinder.My problem is that when i go to use my heater my abs and brake light comes on when i put my heater on...Also i notice my truck starts to backfire...I have tried to pinpoint where the short can be if thats the problem.Im not sure but its by my abs pump.I zip tied the wires up and my heater started working and the abs and brake light goes off..Now after awhile the abs and brake light comes back on and my heater dont work again....Can you please hel


Under the dash on the passenger side you will find the resister block for the fan motor. it's near the fan mounted on the duct work. there are a couple wires going to it connected by a plug. there are 2 or 3 screws holding it in. replace that and ... Chevrolet S 10

After having some work done in my 05 Expedition we started having electrical system problems as follows: Door Lights/Interior lights don't come on when the door is opened. Interior lights only come on when you force them on with the Display Dimmer switch and use the interior light switches. Auto Headlights fail to shut-off on their own from time to time. The work that was done was specific to replacing the head gaskets so I am not sure what they could have done, but they claim it would not h


The problems you have are two different modules. The interior lights are run by the body control module(BCM) and the headlights are run by the day time running light module(DRL). I can't think of any thing that they could have done to create these pr ... 2005 Ford Expedition

My front brakes on my 06 duramax seems to be stuck part way on. everything worked fine until i left it sit for work and got back in drove it home and it locked up brakes were hot plus if i put the e brake on and use no throttle in D it still moves is that connected in any way?


... 2006 GMC Sierra

2000 Mercury Marquis lighting problem.No brake lights,except one in back window is working,no headlights,dashlights,turn signals or flashers. Replaced LCM with used one,don't know if it's a good one but brake lights work now. Still no headlights,turn signals light but don't flash, flashers work but real fast and erratic, and no dash lights. Did I get a bad module or do I have other problems.Anyone have diagrams?


All these functions are controlled by the LCM, this module is unique to each cars paticuliar accessory package, u may have the wrong one or like u said it is defective, the module can be self tested for proper function by a ... Mercury Grand Marquis

We've just had a big rain storm and I was out getting errands done when all of a sudden it was as if my power brakes were'nt working. It was very hard to push the brake pedal down, although I still had brakes, also the car started to run rough and it eventually died. After a few minutes I got it restarted and it made it alittle bit further and died again but this time it would not restart. The car has been running fine up until now. The only thing I can figure is something got wet, I did go thro


Check the brake booster compartment to see, if it full of water. it is located under the cabin airfilter on drivers side engine firewall.there is a water drain at the bottom of this compartment that sometimes get blocked by leaves and other things.wh ... 2002 BMW 5 Series
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.6111 seconds