Having problems with your 2001 Buick Century ?

Camshaft position sensor circuit range, problems code P0341

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

I have usually found the camshaft position sensors to go bad. sometimes the connector can go bad as well. I would install a new sensor and unplug battery for 2 minutes and restart car and see if light stays off.
Repair Help & Product Troubleshooting for 2001 Buick Century

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Camshaft position sensor circuit range, problems code P0341


I have usually found the camshaft position sensors to go bad. sometimes the connector can go bad as well. I would install a new sensor and unplug battery for 2 minutes and restart car and see if light stays off. ... 2001 Buick Century

I have a 1996 saab 900S 2.3L with a check engine light obd2 code p0341 camshaft position sensor out of range. I am told this engine does not have a cam position sensor but that saab uses this code for other ignition problems. BTY the runs OK. What can I do to diagnose this problem?


I also have a saab 900 s with the 2.3 L. I started throwing the same code. I found out from the Hanes manual that the CMP sensor is integrated into the distributor on this model. Which explains why the distributor costs so much. You might want to che ... 1996 Saab 900

My 2003 Tracker 4-cyl 2.0L quit going down the road. Getting the P0340 code 'Camshaft Position Sensor Circuit Fault'. Replaced the camshaft position sensor to no avail. Wiring appears to be OK. Does this motor have a timing belt? Is there any way to narrow this problem down? Can the crankshaft pos. sensor cause this problem?


Yes it can. Usually a cam sensor (on GM's) will cause it to go into 'limp' mode. I do believe it is a timing belt on this model. Hopefully that did not break. If it did the engine would definately sound "different" while trying to start. ... Chevrolet Tracker

We have a 2004 gmc savana 2500 4.8. It started out by not going over 50 then went to not going over 25. We have replace the spark plugs, the mass air flow sensor, and the throtle position sensor. We have had codes ran on itand got these four. first P0101 (maf) mass air flow circuit range problem. Second p0154 02 sensor circuit no activity (bank2 sensor1) third p0155 02 sensor heater circuit malfunction (bank 2 sensor1) forth p0300 random/multiple misfire. Those are the codes. Also we have found


... Cars & Trucks

We have a 2004 gmc savana 2500 4.8. It started out by not going over 50 then went to not going over 25. We have replace the spark plugs, the mass air flow sensor, and the throtle position sensor. We have had codes ran on itand got these four. first P0101 (maf) mass air flow circuit range problem. Second p0154 02 sensor circuit no activity (bank2 sensor1) third p0155 02 sensor heater circuit malfunction (bank 2 sensor1) forth p0300 random/multiple misfire. Those are the codes. Also we have found


... Cars & Trucks

1996 F-150 4.9L 6 cyl Crankshaft sensor question: Ledsled said: All fuel injected engines use the TFI-IV system, and I'm not aware of a CKP (cranksheft position sensor), this system only has a CPS (camshaft) Hall effect in the distributor. What problems are you having???? No spark? The code that it's pulling is Crankshaft Position Sensor B Circuit Malfunction. PO385 Vehicle starts but will not pass MA emissions inspection because of the PO385 code. More help is needed please.


Actually according to my Ford EVTM your truck uses a DIST, ICM and a misfire sensorHowever, that is only realitive to the fact the the P0385 = coil code NOT a CKP/CMP code which you have neithera P0385 indicates that the self ... 1996 Ford F150 Regular Cab

But the check engine light came on yesterday. I checked the car using a OBD scanner, and it found 3 codes for the car: P0012- Camshaft position timing over retarded bank 1 P0301- Cylinder 1 misfire detected P0327 - Knock sensor 1 circuit low bank 1 or single sensor. After I checked the codes, (I did not erase any code) the check engine light went off . I do not notice any problem in the performance or running of the car and am generally not seeing any differences like fuel smells, lea


I think your idea is wrong. A fault code indicates a problem, though, cars can be used normally, but the problem is there, need to be addressed.or you can ask the 24 hrs live technical support http://www.diyobd2.fr/service/ , they will like to help y ... 2002 Mazda Miata

The check engine light came on yesterday on my 2002 Mazda Miata LS with about 140k miles on her. I checked the car using a OBD scanner, and it found 3 codes for the car: P0012- Camshaft position timing over retarded bank 1 P0301- Cylinder 1 misfire detected P0327 - Knock sensor 1 circuit low bank 1 or single sensor. After I checked the codes, (I did not erase any code) the check engine light went off . I do not notice any problem in the performance or running of the car and am general


... Mazda Cars & Trucks

Code P0336 Crank sensor position A circuit range dash performance, on a 2003 Pontiac Bonneville, engine dies while driving. Can usually be restarted. Crank Position sensor was replaced but still have same problem.


... 2003 Pontiac Bonneville

Complex! 2006 SC430 was running perfectly. One day started missing. Scanned it, "Misfire on cyl 5." Couple days later, running even rougher, scan said "Misfire cyls 1, 3, 5, 7." Couple days later, wouldn't start at all. Scan said, "Camshaft position sensor circuit problem," and "Crankshaft position sensor problem." Checked continuity of both wires, tested good. Replaced the camshaft position sensor anyway, no change. I hate to replace the crank position sensor, because if it was bad, I


... 2004 Lexus SC 430

1998 Jeep Cherokee engine runs rough.I used a code reader and the code that comes up is PO340 camshaft position sensor circuit malfunction.There is no camshaft sensor on this engine 4cyl 2.5L that I am aware of the closest part that i am aware of is the timing sensor plate in the bottom of the distributer so I replaced it.I also replaced plugs.plug wirers,distributer cap and rotor.The rough idel is still presant and the same code is coming up on the code reader.I did erase the original code and


Check your crankshaft sensor could be a possiblity, check the compression ... Jeep Cherokee

We have a 2001 sebring 3.0l v6. It lost power after an accereration, no noises or anything. Now it will not come out of park if the engine is running. We ran a diagnostic on the computer and got the following codes P0403 (exhaust gas recirculation control unit), P0765 (Shift solenoid d malfunction), P0760 (shift solenoid c malfunction), P0340 (camshaft position sensor A circuit) and P0335 (camshaft position sensor A circuit malfunction). Can anyone help?


The P0403 error code is the EGR system that consists of a valve and solenoid controlled by the engine computer. Replace the EGR valve. The P0765 and P0760 error codes are transmission related. Replace the transmission shift solenoid. \01 ... 2001 Chrysler Sebring

My car is showing PO344 (Camshaft Position Sensor A Circuit Intermittent) as a problem it's having... I replaced the camshaft sensor about 2 years ago when I was having a similar problem; could the sensor have gone out, or would this be a different problem?


All ways, the camshaft position sensor signal sent to the ECM is intermittent\015\012\015\012The Camshaft Position Sensor is an electronic device used in an engine \015\012to record the rate at which the camshaft is spinning. This informa ... Dodge Stratus

My 99 Volvo s80 t6 is reading a bunch of codes p0118, engine coolant temp sensor circuit high input.p0238, turbo/ super charger, boost sensor A circuit high.p0236, turbo/ supercharger boost sensor a circuit range performance.p0050 Ho2s heated, o2 sensor / control circuit bank 2 sensor 1. And p0114,(iat) intake air temp sensor circuit high temp. I hear that the transmission control module could be causing all these problems? I really dnt know thought any ideas please help!!!!


... Cars & Trucks

Getting the following codes from a 1997 Pontiac Grand Am....... PO121 TPS / Pedal Position Sensor A CKT Range / Perf Also, PO341 Camshaft Position Sensor A - Bank 1 CKT Range/Perf. Any thoughts on the


Po121 means that there is a problem with the throttle position sensor ( tps). or in the wiring or connector, most likely its the tps that is bad. first remove connection from tps, heres how to test. use an ohms meter and hook a lead to top or bott ... 1997 Pontiac Grand Am

Engine Light I have a 2000 RX 300 and the engine light just came on - the oil was recently changed; I checked the gas cap like manual said, could there be other major problems has anyone had this problem? This is Beckster777 with rx300 engine light on (emmissionwiz) O'rilleys gave these codes: P1135 A/F sensor heater circuit malfunction bank 1 sensor 1 P1130 a/f sensor circuit range performance malfunction bank 1 sensor 1 P0171 system too lean bank 1


Check the wiring to sensor 1 bank sensor 1 for possible damage from the exhaust, also make sure the connector to the O2 sensor (they called it a air/fuel sensor, incorrect) is in good condition and not contaminated with oil or water intr ... 2000 Lexus RX 300

I have a 1995 420a swap in a 1996 eclipse rs the wiring was all different for a lot of the sensors and the ecu. I use the 96 harness. I had three of the same looking connectors that went to the ign coil and the camshaft angle position sensor couldn't find the purpose of the last connector once I match the connectors in the right position the car started but ran ruff I put the diagnostic on it and it read code p0340 camshaft sensor circuit 1 malfunction I replaced the sensor and the car hasn't st


... Cars & Trucks

By brdgtrmbrt on Jun 03, 2010 " " I got a diagnosis of my 2002 dodge neon's problem that caused my check engine light to come on and the code that I received was P0705. The definition reads: Transmission range sensor circuit malfunction. then probable cause-open or short circuit condition-poor electrical connection- misadjusted TR sensor- failed TR sensor. That is what my printout reads. My 2002 dodge neon currently has 86,000 miles. I went to a parts store to buy a new transmission range sens


My though would be to jack up the rear wheels and spin them both. Sounds like you have a brake issue or wheel bearing resisting. Your rear wheel bearings may also contain the speed sensors. (Not 100% sure on your model, but many do) While off of the ... 2002 Dodge Neon

2004 f150 5.4 triton 4x4. Engine started missing yesterday, worse today. Took to autozone ran code, code said camshaft position sensor, o2 sensor bank1 rich bank2 lean, missfire on cylinders 7 5 3 1. Replaced camchaft position sensor same problem


Change the o2 sensors and this will correct the problem dont forget to have the light turned back out ... 2004 Ford F150

2002 3.8 mustang throws codes p0603 & p1518. Driving at normal speeds and starts kicking in and out of overdrive. Just changed the crankshaft position sensor it seemed to help. Wondering if maybe code 0603 may be a source of the problem or the camshaft position sensor, even though its not throwing the code for it?


... Cars & Trucks

How to troubleshoot P0340 Camshaft Position Sensor Circuit Malfunction code after replacing the sensor?


Where is the camshafts on BMW z3 1997 ... 2006 Ford Escape

2006 Ford Expedition, replaced camshaft sensor two months ago after getting P0022 Intake Camshaft Position Timing-Over-Retarded (Bank 2). Now having simular problems, engine light on, checked code, same code as before... So what could cause this sensor to go out again, or could it have already gone again?


... Cars & Trucks

My check engine light goes on almost daily and throws the code for Camshaft positioning sensor not responding. Only problem is that according to the dealer, my car doesn't have a camshaft positioning sensor.. Does anyone have any clue what's going on? It's a 2.0 4 cyl turbo


Your car does have a crankshaft position sensor; have that checked. ... 1996 Saab 900

P1345, won't start, sputters and snorts when cranking starter. on a 2000 chevrolet astro awd. prior to present problem, replaced timing chain, spark plugs, distributor cap and rotor. it started and ran fine but ses light remained on. kicked out a p0340. pulled the distributor cap and rotor, checked the screws holding the camshaft positioning sensor, and returned the cap and rotor. it wouldn't restart. replaced the camshaft positioning sensor and reset the pcm trouble code memory. then it


P1345 code problem:------\015\012\015\012This\015\012code is set when either the CAM\015\012sensor is not in it's correct position, or when the crank and cam sensor don't\015\012agree on position of ... 2000 Chevrolet Astro

P0344-Camshaft Position Sensor A Circuit Intermittent Bank 1 Spitting and sputtering We've fixed the Camshaft Position Sensor twice, replaced the timing belt and put new plugs and wires on it. What else can possibly be the problem???


I can sympathize with you here because I am goin through the same thing. I'm not sure how much help I will be but I can tell you some of the things I have tried. I have replaced 1 of 4 of my oxygen sensors, camshaft sensor, mass air flow sensor, plug ... Chrysler PT Cruiser
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.4439 seconds