Having problems with your Chevrolet Silverado 3500HD ?

2003 Chevy Silverado- The lumbar pump has pumped the seat up and has quit working. I didn't bother to check the fuses because the passenger seat works. I believe they are on the same circuit. The switch seems fine. I can hear the contacts working. Checked switch for resistance with meter. I believe the pump is bad. How do you replace the pump? Are there any other possibilities?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Chevrolet Silverado 3500HD

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2003 Chevy Silverado- The lumbar pump has pumped the seat up and has quit working. I didn't bother to check the fuses because the passenger seat works. I believe they are on the same circuit. The switch seems fine. I can hear the contacts working. Checked switch for resistance with meter. I believe the pump is bad. How do you replace the pump? Are there any other possibilities?


... Chevrolet Silverado 3500HD

I got a f250 97 powerstroke it died like it just ran out of fuel and would not start. After looking I found that I was not getting fuel to the engine. Now I have two tanks with a pump in both. Dont think both pumps would fail at same time. So I checked the selector switch on dash it seems to be working fine. Checked the transfer box from one tank to another it is working. Also checked all fuses good there. I tried beating on tank to get fuel pump to run did nopt help. Tried changing selonoids ar


Pump is not in the tank. ... 1997 Ford F250 SuperCab

I have a 2002 Chevy S10 Crew Cab Pickup. The Windshield Washer Pump does not work. I have replaced the pump and checked wiring from the pump to the steering console and the ground side wire. I can get the pump to work if, I jump power to the steering console wire. That would leave the power to the switch, the switch, or a fuse. All of the fuses in the cab seem to be fine. The engine fuse box had a spot for the windshield washer pump, but no connections for a fuse to go into that spot (not even s


Looking at the Diagram the power for the washer pump goes from the multi-function switch on column to the pump for domestic vehicles and the power fuse also runs the wipers so if it was the fuse your wipers would not work. The fuse in the PDM in the ... Chevrolet S 10

Car will not start. car will run for a moment or two if I pour gas in the fuel injection manifold. The fuel gauge is pegged to overfull. all other gauges seem to work fine. Fuel gauge remains pegged even with the fuel pump electric wires disconnected. I believe it is a bad fuel pump relay or the the low oil pressure sensor switch is disabling the fuel pump relay. However I cannot locate the fuel pump relay?


The oil pressure sending unit will be the problem for that primes the pum when you turn the key to the on position. You will hear the fuel pump running for 5 seconds when doing that. If the pump is running when you have the key turned to the ON posit ... 1992 Buick Roadmaster

Ignition switch So the wire to the ignition switch seem to be shorting or something, when I try to turn on the car on all the dashboard lights dont work, neither does the radio auto headlights, heater or the fuel pump. So I took the radio out to take a look at the ignition switch. And when I move the wires around it turns on just fine. I checked fuses and have no blown fuses so im at a lose on what else to do.


My bet is the ignition switch itself or the connector on the switch is bad.You say things seem to work when you move the wires. This is classic indication that the switch is bad. Let us know if this fixes the problem. Robert ... 2001 Chevrolet Malibu

The van has a new fuel pump, which pep boys told us that would get the van to turn or. it still is not working. can the spark plugs have anything to do with it not turning on. we have checked the fuses and they seem to be fine. now the switch that is in the rear of the van, does not seem to have any power. we had it tested and the light did not turn on.


If the inertia switch for the fuel pump has no power, there could be a break in the wire somewhere leading to it, or a fusible link has blown, if so equipped.\015\012\015\012Sometimes, the inertia switch itself goes bad, that wouldn't exp ... 1997 Ford Windstar

I'm working on 2000 chev S10 pickup. the blower fan doesn't work from dash controls. I jumpered the moter and it spins fine, I have tested the wiring at the switch and I believe the switch is working fine. When I went to the parts store to check out a new switch, the style in the vehicle is for 2001 vehicles. when I try to trace the wires from the switch to the blower resistor the color of the wire switch somewhere, maybe at the firewall connections. at the blower motor connection, the blue wire


Did you remove and inspect the blower motor resistor - a bad one can stop the blower and make for some hot wires ... 2000 Chevrolet S-10

Put new fuel pump and filter on my 88 dodge dakota,now pump not working can not hear it kick in checked voltage every where voltage seems fine and also checked fues's they seem fine what could be problem than ks


Yes, usually in the power distribution box , and it is replaceable. ... 1988 Dodge Dakota

2008 Ford Taurus X, drivers seat heater w/n work. WHen you press the button for the seat heater to come on the light flashes and goes out..stays on as long as you hold the button down. When you release the button the light goes out. Seat does not heat. The passenger seat works fine. I checked the fuses but everything seems fine. Althought I did not see a specific fuse for "drivers" seat heater I did see one for "heated seat module". I swapped it out with a module of the same amp and there


The heated seat module is most likely the problem here. It acts like a latching relay to bring on the heating element in the seat. One push of the button latches the "relay", and another push of the button causes it to "unlatch". This may have a stor ... 2008 Ford Taurus X

1996 monte carlo windows will not go down or up from drivers side master switch and pass side switch will only go down. I know both switches are good, I pulled them and put in 1995 monte and they work fine in all postions. pulled the cover off pass door and tested motor directly works fine up and down. checked the continuity of each wire between pass door and drive door all fine. Its seems like I have a ground problem. does anyone know where the ground is being pulled from for the motors? is it


It's in the circuit relay in the drivers master control pannel switch inorder to opperate these windows you actually have to short the power to ground inorder to move the windows up or down you need to repair/ replace the switch, \015\012I had ... Chevrolet Monte Carlo

The windshield washer will not work on my 2003 Mitsubishi Eclipse Spyder GTS. I removed the pump and tested it on a power supply and it worked fine. When I took a voltmeter to the cable that attaches to the pump on the car itself, it read that there was no voltage. I have checked several fuses but none seem broken and I am not sure which one is the correct one. All other electronics on that wire harness work, too: the fog lamps, headlight, and everything else work fine, just the windshield washe


... Mitsubishi Eclipse Spyder

1996 vw jetta problem with the headlights. The daytime running lights work fine the high beams work fine, but when you turn on the lights from the switch the driver side headlight turns off. I've checked the fuses and everything seems fine. Could it be the switch?


I don't have a wiring diagram ,but on most cars I would say your low beam bulb is bad. Try swapping sides to see if the problem goes with it, or just replace the bulb. You can always keep the new one until needed someday... shadetree mech by necessit ... 1996 Volkswagen Jetta

I've a 04 transporter t5. The driver's side windows wont work. the switches are working. it seems there's no power to the switch. Even when the lights are turned on the switches wont light up. Have checked the wires from the cab to the controller on the window motor. wiring seems fine. Any ideas??


... Volkswagen Camper

While driving to school today, my car died while driving. The battery if fine because the radio kept playing and the car turns over when I turn the key but it won't start. I checked the belts and they're fine. I changed the ignition cables. I checked my oil. I had a half a tank of gas when this occurred. I checked the spark plugs and they seem fine. I checked the EGI relay and it works fine as well. I've been reading that it could be the fuel pump or fuel filter, is this accurate? Also,


First you need to see if you have a fuel or ignition problem. Also check and make sure the timing belt didn't break. Chek and make sure you are getting spark. Check the timing belt first. You need to know if the crank and cam are both turning. The v= ... 1999 Mazda MX-5 Miata

98 Mercedes SL500 - power mirrors and power seats will not work. Checked fuses all okay. By accident have now found that both mirrors and seats will work with either door open. Can manually work the interior light switch in door frame. Button in = no power to mirrors or seats. Button released = mirrors and seats work fine. Any suggestions.


... 1998 Mercedes-Benz SL-Class

I own a 200 model 320 W163. Both heated seats do not work, the lights on the dash come on and after a time switch to the single light, but there is no heat in either seat. I have checked the fuse box under the dash and cannot finds any reference to the heated seats on it, I also did not find any faulty fuses and all relays appeared to work, as I swapped them around and everything else continured to work fine. I also looked under each seat and all the wires appear to be plugged in. Is there a se


Did you check the fusebox on the passenger side kick panel under? There is fuses and relays over there. ... Mercedes-Benz ML320

I have a 2000 nissan sentra. It has no spark and no power to the fuel pump? Checked all the fuses and relays..Every thing seems to e fine..I put my voltage meter into the fuse block and no power to the fuse for the pump?Everything else seems to work fine...Computer?


... 2000 Nissan Sentra

Power seat we just got the van. The drivers seat is power but it won't move. There are some wires laying behind the seat. The seat appears to be wired. We were wondering if those wires could go to the control switch that moves the seat. There doesn't seem to be any power to the control switch but there is power as the power seat is on the sam circuit breaker as the power door locks and they work fine. We would appreciate any help you can offer. Thank You: Confused.


I have problem with deats, ti thing that there is no power coming to the seat so that can moveand that is with all the seats in the car. i would be appreciate if you can tell me where the fuse for the seats power is located. thank you ... 1995 GMC Safari

My step-sons 99 jeep Cherokee has been running fine and he went to work everything was fine got off work went out to leave now it won't start I went to his work it appears not to have any spark at the plug wires gas gauge which he says works is on empty so we put about 3 gallons in and still is not registering and still doesn't start sprayed starting fluid no go the odometer while switch is on says (no bus) would it be a control module or fuel pump I have no Manual at this time and have checked


If the dash is reading no bus, check the connections on the ECM, the vehicle computer, and check the fuses and relays in the power distribution box under the hood. Your problem is going to be in one of those areas or the ECM has shorted out. ... 1999 Jeep Grand Cherokee

Driver side cooling fan was working and passenger side was not, switched 4 pin relays around multiple times, now passenger fan works and driver side does not work and I can't get the driver side to work by switching relays. Runs hot, uses coolant and oil, runs about 170-185 as long as the car is moving, runs at 200-230 while idle, checked all fuses and they are fine. Thought maybe it was the relays, thermostat or the water pump if it was replaced with a non-original part.


The coolant sensor controls these fans,one is for moderate cooling,the other kicks in when the temp gets up higher,so change the coolant sensor.Turn the ac on max cool,see if the cooling fans both come on,and let me know. ... 2001 Chevrolet Monte Carlo

I have a 1994 6.5 chevy diesel pickup that has a problem with the lift pump staying on. I have replaced the injector pump 3 time (all bad). I replaced the lift pump relay and it worked better, but would run rough and die sometimes. I bypassed the relay with a switch and it seems to run fine (this is the way we ran our over the road truck in the 60's). The oil pressure gauge always registers 50# and seems to operate properly. Is the relay connected to a different sensor? Thanks


... 1994 Chevrolet K2500

My turn signals and hazard lights were working intermitently. now they have stopped working completely, the multi function switch for the lights is working as i checked it with an ohm meter. the fuse is fine(first thing i checked) and i cant seem to locate the flasher. It isnt where it says it is supposed to be in the book.


The turn signal flasher is located above the fuse box under the dash on you drivers side of the vehicle. It will look like astandard relay. It is in the top row center. Hope this helps out.\015\012\015\012Best of luck ... 2001 Jeep Grand Cherokee

When driving my 2000 pontiac sunfire, I will use my brakes and sometimes they go to the floor and the car barely comes to a stop. Sometimes they work fine though. If I pump the brakes they work fine as well. The times when the brake pedal goes to the floor, it feels as if not all the brakes are working. I have checked for leaks and found nothing.I have bled the brakes and there is lack a of pressure to some of the brakes. I believe it might have something to do with my ABS braking system.


Try this ABS bleeding procedure:\015\012\015\012WITHOUT TECH 1\302\256 OR T-100\302\256\015\012Do not place your foot on the brake pedal through this entire procedure unless specifically instructed to do so. ... 2000 Pontiac Sunfire

The wipers wont work unless you hold the washer button on the back wiper works fine have checked the fuses and the motoor seems to be working fine and replaced the switch on the steering column


What year is your car?? ... Plymouth Grand Voyager

Low beams wont work on 1990 camry changed globes checked fuses, changed head lamp relay . switch seems fine , I was playing with the head lamp realy and it seemed they worked, and the next day they didnt so i have replaced relay still no go and i cant get high beam now unless i pull indicator back towards me to flash high beams , with indicator pushed forward in its traditional constant high beam this function will not work as i did previously either, so no high or low beams now can you help


... 1991 Toyota Camry
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.4387 seconds