Having problems with your 1992 Jeep Wrangler ?

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer

Posted / edited by AnonymousUser on : 10-12-2018

Answers :

    \015\012
  1. timing cover is leaking oil betwwen cover and block
  2. \015\012
  3. Disconnect the negative battery cable.
    \015\012
  4. \015\012
  5. \015\012 Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
    \015\012
  6. \015\012
  7. \015\012 Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
    \015\012
  8. \015\012
  9. \015\012 Remove the accessory drive brackets attached to the timing cover.
    \015\012
  10. \015\012
  11. \015\012 Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
    \015\012
  12. \015\012
  13. \015\012 Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
    \015\012
  14. \015\012
  15. \015\012 Remove the timing case cover front seal and gasket from the engine.
    \015\012
  16. \015\012
  17. \015\012 Cut off the oil pan side gasket end tabs and oil pan front seal \015\012tabs flush with the front face of the cylinder block. Remove the gasket \015\012tabs.
    \015\012
  18. \015\012
  19. \015\012 Clean the timing case cover, oil pan and cylinder block gasket surfaces.
    \015\012
  20. \015\012
  21. \015\012 Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.
    \015\012
\015\012

To install:
\015\012

    \015\012
  1. \015\012 Install a new seal in the timing cover using a suitable seal installation tool.
    \015\012
  2. \015\012
  3. \015\012 Apply sealer to both sides of the replacement cover gasket and \015\012position the gasket on the cylinder block. Cut the end tabs off the \015\012replacement oil pan gasket corresponding to those cut off the original \015\012gasket. Attach the end tabs to the oil pan with sealer.
    \015\012
  4. \015\012
  5. \015\012 Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
    \015\012
  6. \015\012
  7. \015\012 Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
    \015\012
  8. \015\012
  9. \015\012 Insert timing case cover alignment tool J22248 or equivalent, in \015\012the crankshaft opening. Install the cover-to-cylinder block bolts and \015\012tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil \015\012pan-to-cover bolts to 11 ft. lbs. (13 Nm).
    \015\012
  10. \015\012
  11. \015\012 Remove the cover alignment tool and position a replacement oil \015\012seal on the tool with the seal lip facing outward. Apply a light coat of\015\012 sealer to the seal and a light coat of oil to the crankshaft. Install \015\012the seal on the timing cover.
    \015\012
  12. \015\012
  13. \015\012 Apply a light film of oil to the vibration damper hub seal \015\012contact surface. Install the vibration damper using a suitable \015\012installation tool.
    \015\012
\015\012

Do not hammer the damper into place as damage may result to the damper or engine.
\015\012

    \015\012
  1. \015\012 Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
    \015\012
  2. \015\012
  3. \015\012 If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
    \015\012
  4. \015\012
  5. \015\012 Install the accessory brackets.
    \015\012
  6. \015\012
  7. \015\012 Install the fan and fan shroud.
    \015\012
  8. \015\012
  9. \015\012 Install the drive belt(s) and adjust to the proper tension.
    \015\012
  10. \015\012
  11. \015\012 Connect the negative battery cable.
    \015\012
  12. \015\012
  13. \015\012 Start the engine and check for leaks
  14. \015\012
  15. .
    \015\012
COULD HAVE DRIVEN CRANKSHAFT SEAL IN CROOKED.IF YOU DID NOT USE SEALER ON END TABS TO THE OIL PAN.IT WILL LEAK.ALSO IF YOU DID NOT PUT SEALER ON TIMING COVER GASKET YOU WILL GET A OIL LEAK AT BOTTOM OF TIMING COVER.
Repair Help & Product Troubleshooting for 1992 Jeep Wrangler

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loading ...

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0055 seconds