Having problems with your 1994 Toyota Corolla ?

How to change starter on 1994 corolla - 1994 Toyota Corolla

Posted / edited by AnonymousUser on : 10-12-2018

Answers :

The sizes given are the wrench sizes needed to perform the step.
1. Remove the negative battery cable from the battery.
2. Remove the hose that connects the air cleaner to the throttle body.
3. Remove the top of the air cleaner box (4 clips on the corners).
4. Take out the air filter. Disconnect the sensor on the side of the air cleaner.
5. Remove the three bolts (2 - 12mm, 1 - 10mm) that hold the bottom of the air cleaner box to the inner fender and remove the box.
6. Disconnect the two rubber hoses on the top of the air canister (one large, one small).
7. Loosen the clamp bolt (10mm) (be careful as there is a non-captive nut that will drop if you remove the bolt completely) and slide the air canister out.
8. Remove the two bolts that hold the fuel filter on to its bracket (10mm). It is the same bracket as the air canister's.
9. Remove the air canister/fuel filter bracket by removing the four bolts that hold it in place (10mm).
10. Remove the wire harness/hose bracket directly in front of the top starter bolt (12mm) - this will facilitate your ability to get a socket wrench on the starter bolt. On my car it was RIGHT in the way!
11. Loosen the top starter bolt (14mm).
12. Loosen the bottom starter bolt (14mm) and remove it completely.
13. Hold the starter up and remove the top bolt completely. Flip the starter over and place it on the drive axle below with the wiring facing up.
14. Disconnect the solenoid plug and the starter cable (12mm).
15. Remove the starter by snaking it through the driver's side of the motor compartment. There's enough room if you're patient - be careful not to snag anything and damage it.
16. Snake the new starter down through the driver's side reverse of the way the old one came out. Lie it on the drive axle and connect the solenoid connector and the cable.
17. Flip it over and up into place. Hold it in place and start the top bolt. Tighten it by hand enough that the starter stays in place by itself.
18. Start the bottom bolt; tighten it up all the way.
19. Tighten the top bolt the rest of the way.
20. Connect the battery cable and try the starter - before you put everything back!
21. Replace canister/fuel filter bracket and bolt the fuel filter in place.
22. Slide the air canister in and tighten the clamp bolt. Connect the two rubber hoses on top of it.
23. Install the bottom of the air cleaner box; plug in the sensor.
24. Put in the air filter and then replace the top of the air cleaner.
25. Connect the big hose from the air cleaner to the throttle body.
NOTE: You may have to reset the "check engine" light when you're finished (I think starting the car when we check it in Step 20 can freak out the computer since there are still things disconnected). To do this, find the fuse block on the driver's side of the engine compartment; remove the 15A EFI fuse for 30 seconds. Put the fuse back in - the light should now be reset.
That's it! Shouldn't need another one for another 150,000 miles!

A helpful rating and an testimonial would be greatly appreciated if you are satisfied with my solution ...
Repair Help & Product Troubleshooting for 1994 Toyota Corolla

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loading ...

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0090 seconds