Having problems with your 1995 Honda Accord ?

I want to know how to fix the alignment on my 1995 honda accord ex.

Posted / edited by AnonymousUser on : 17-01-2022

Answers :

Before making wheel alignment adjustment, perform the following checks:
\015\012
    \015\012
  1. Tires should be equal in size and runout must not be excessive. Tires and wheels should be in balance, and inflated to manufacturer's specifications.

  2. \015\012
  3. Wheel bearings must be properly adjusted. Steering linkage and suspension must not have excessive looseness. Check for wear in tie rod ends and ball joints.
  4. \015\012
  5. Steering gear box must not have excessive play. Check and adjust to manufacturer's specifications.
  6. \015\012
  7. Vehicle must be at curb height with full fuel load and spare tire in vehicle. No extra load should be on vehicle.
  8. \015\012
  9. Vehicle must be level with floor and with suspension settled. Jounce front and rear of vehicle several times and allow it to settle to normal curb height.
  10. \015\012
  11. If steering wheel is not centered with front wheels in straight-ahead position, correct by shortening one tie rod adjusting sleeve and lengthening opposite sleeve equal amounts.
  12. \015\012
  13. Ensure wheel lug nuts are tightened to torque specifications
Ride Height Adjustment

Before adjusting alignment, check riding height. Riding height must be checked with vehicle on level floor and tires properly inflated. Passenger and luggage compartments must be unloaded. Bounce vehicle several times, and allow suspension to settle. Visually inspect vehicle from front to rear and from side to side for signs of abnormal height.
Measure riding height. See figure. Riding height between left and right sides of vehicle should vary less than 1′ (25.4 mm). If riding height is not within specification, check suspension components and repair or replace them as necessary.
Wheel Alignment Procedures

Honda recommends using commercially available computerized 4-wheel alignment equipment. Follow equipment manufacturer instructions to obtain vehicle alignment settings. Use following procedures for necessary adjustments.
Civic Camber Adjustment
Compare camber settings with vehicle manufacturer recommendations. If camber is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck camber.
Civic Caster Adjustment
DO NOT use more than 2 shims. If more than 2 shims are required to adjust caster angle, check for bent or damaged suspension components.
Compare caster settings with vehicle manufacturer recommendations. If caster is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck caster.
Civic Toe-In Adjustment

\015\012
    \015\012
  1. Secure steering wheel in straight-ahead position. Measure front wheel toe-in. If adjustment is needed, loosen tie rod lock nuts. Turn both tie rods equally in the same direction until front wheels are in straight-ahead position and toe-in reading is correct. Tighten tie rod lock nuts. Reposition tie rod boots if twisted.
  2. \015\012
  3. Ensure parking brake is released. Check rear wheel toe-in. If adjustment is needed, hold adjusting bolt on rear compensator arm and loosen lock nut. See figure. Adjust rear toe-in by sliding rear control arm until rear toe-in is correct. Install NEW lock nut, and tighten it while holding adjusting bolt.
Wheel Alignment Specifications

\015\012
    \015\012
  • Camber - Measurement in degrees.\015\012
      \015\012
    • Front: 0 (range -1 to 1)
    • \015\012
    • Rear: 0.33 (range -1.33 to 0.67)
  • \015\012
  • Caster - Measurement in degrees.\015\012
      \015\012
    • 1.17 (range 0.17 to 2.17)
  • \015\012
  • Toe-In - Measurement in inches (mm).\015\012
      \015\012
    • Front: -0 (0)
    • \015\012
    • Rear: 0.08 (2.0)
  • \015\012
  • Toe-In - Measurement in degrees.\015\012
      \015\012
    • Front: 0.00 (range - 0.16 to 0.16)
  • \015\012
  • Toe-Out On Turns - Measurement in degrees.\015\012
      \015\012
    • Inner: 41.00
    • \015\012
    • Outer: 33.50
Torque Specifications Ft. Lbs (N.m)

\015\012
    \015\012
  • Rear Control Arm Adjusting Bolt: 48 (65)
  • \015\012
  • Spindle Nut: 136 (185)
  • \015\012
  • Tie Rod Lock Nut: 41 (55)
  • \015\012
  • Wheel Lug Nuts: 80 (108)
hope this helps you out.
This is something you should take to your local alignment shop and have them do, they have specialized equipment to do this.
Repair Help & Product Troubleshooting for 1995 Honda Accord

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loading ...

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0094 seconds