Having problems with your 1996 Chevrolet Blazer ?

Trouble replacing ball joints on a '96 Chevy Blazer. I am on day 2 of this project. I have removed all the bolts from both upper and lower ball joints and still can't get them out. I also have removed the steering knuckle bolts also no help. I have also removed the spindle nut still no help. It was late when I got the spindle nut off so I havent put alot of effort in since then but it didn't appear to want to budge. Whats next?

Posted / edited by AnonymousUser on : 21-09-2020

Answers :

    \015\012
  1. Support the weight of the control arm at the wheel hub.
  2. \015\012
  3. Measure the distance between the tip of the ball joint stud and the grease fitting below the ball joint.
  4. \015\012
  5. Move the support to the control arm and allow the hub to hang free. Measure the distance again. If the variation between the two measurements exceeds 3 / 32 in. (2.4mm) the ball joint should be replaced.
\015\012\015\012
REMOVAL & INSTALLATION\015\012Raise and support the front end on jackstands.
\015\012\015\012
    \015\012 \015\012
  1. Support the lower control arm with a floor jack
  2. \015\012
  3. Remove the wheel.
  4. \015\012
  5. Remove the lower stud cotter pin and loosen, but do not remove, the stud nut.
  6. \015\012
  7. Loosen the ball joint with a forcing-type ball joint tool. It may be necessary to remove the brake caliper and wire it to the frame to gain enough clearance.
\015\012\015\012
    \015\012
  1. When the stud is loose, remove the tool and ball stud nut.
  2. \015\012
  3. Install a spring compressor on the coil spring for safety.
  4. \015\012
  5. Pull the brake disc and knuckle assembly up and off the ball stud and support the upper arm with a block of wood.
  6. \015\012
  7. Remove the ball joint from the control arm with a ball joint fork or another suitable tool.
\015\012To install:
\015\012Installation is the reverse of removal but please note the following important steps.
\015\012On R-series vehicles, start the new ball joint into the control arm. Position the bleed vent in the rubber boot facing inward.
\015\012\015\012
    \015\012
  1. On C-series vehicles, force the ball joint into position using a screw-type forcing tool. The ball joint will bottom in the control arm. The grease seal should face inboard.
  2. \015\012
  3. On R-series vehicles, turn the screw until the ball joint is seated in the control arm.
  4. \015\012
  5. Lower the upper arm and match the steering knuckle to the lower ball stud.
  6. \015\012
  7. On C-series vehicles, start ball stud into the knuckle. Install the nut and tighten it to 90 ft. lbs. (122 Nm) on 1988-90 models; 84 ft. lbs. (115 Nm) on 1991-94 models and 94 ft. lbs. (128 Nm) on 1995-98 models. Advance the nut to align the cotter pin hole and insert the new cotter pin. NEVER back off the nut to align the cotter pin hole; always advance it!
  8. \015\012
  9. On R-series vehicles, tighten the ball stud nut to 80-100 ft. lbs. (108-135 Nm), plus the additional torque necessary to align the cotter pin hole. Do not exceed 130 ft. lbs. (176 Nm) or back the nut off to align the holes with the pin.
  10. \015\012
  11. Install a new lube fitting and lubricate the new joint
\015\012
\015\0125769f7f.jpg\015\012
\015\01238a57c0.jpg\015\012
ef9480e.jpg
Repair Help & Product Troubleshooting for 1996 Chevrolet Blazer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loading ...

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0099 seconds