Having problems with your 1997 Buick Park Avenue ?

Can't find the starter in my 97 buick park avenue

Posted / edited by AnonymousUser on : 21-06-2021

Answers :

  1. \012\011\011\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0111\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Open the hood of your Buick, and locate the negative battery\012 cable. Remove the bolt securing the cable to the battery, using a \012wrench, then remove and isolate the cable from the battery terminal.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0112\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Place a jack under the front of the car, and raise the \012driver's side of the car. Secure the car on a jack stand positioned \012under the frame of the car, then remove the jack.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0113\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Locate the starter from under the driver's side of the car(right of transmission).More than likely there will be a black cover over the bolts, so take it off first, i think the bolt on the corner holds the cover on and its 12 mm i believe. \012Find the two wiring harness connections on the back of the starter \012solenoid. They are both stud and nut terminals and are marked "B" and \012"S." Remove the retaining nuts from both terminals, using a socket and \012ratchet, then remove the wires from the terminals. Make note of which \012wire came off which terminal; the "B" terminal should have the bigger, \012red wire.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0114\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Locate the two mounting bolts at the front of the starter which should be 15 mm. \012They install from the bottom of the starter, threading up into the \012engine block. Remove both bolts with a socket and ratchet while \012supporting the starter so it does not fall on you. Remove the starter \012from the engine compartment and set it aside.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0115\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Lift a new starter into the engine compartment, and position\012 it up against the engine block. Install the two mounting bolts into the\012 holes in the starter, then thread them into the engine block. Tighten \012the bolts to 32 ft.-pounds of torque with a torque wrench and socket.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0116\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Connect the two wiring harness connections to the starter \012solenoid, matching the large red wire to the "B" terminal and the other \012wire to the "S" terminal. Install the retaining nut on the "B" terminal \012to 12 ft.-pounds with a torque wrench. Tighten the nut on the "S" \012terminal to 22 inch-pounds with a torque wrench.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0117\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Lift the front of the car with a jack, and remove the jack \012stand. Lower the Buick to the ground and remove the jack from under the \012car.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    • \012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\0118\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\011Connect the negative battery cable to the negative battery \012terminal, then tighten the retaining bolt with a wrench. Test the repair\012 by starting the engine, ensuring the starter is functioning properly.
      \011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011\011\011\011\011\011
    \012\011\011\011\011\011\011
Repair Help & Product Troubleshooting for 1997 Buick Park Avenue

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loading ...

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0094 seconds