Having problems with your 1999 Chevrolet Malibu ?

Dashboard lights dont work - 1999 Chevrolet Malibu

Posted / edited by AnonymousUser on : 10-12-2018

Answers :

Try to adjust the dashboard dimmer switch.
\015\012
\015\012or check for fuses:
\015\012CIRCUIT PROTECTION \015\012Fuses \015\012REPLACEMENT \015\012\015\012\015\012\015\012\015\012\015\012Fig. 1: The power distribution box in the engine compartment contains fuses and relays \015\01291146p01.jpg
\015\012\015\012\015\012\015\012\015\012\015\012Fig. 2: Remove the cover from the interior fuse panel (located on the far left of the instrument panel) \015\01291146p66.jpg
\015\012\015\012\015\012\015\012\015\012\015\012Fig. 3: A fuse puller tool is located inside the fuse panel to aid in the removal of the fuses \015\01291146p67.jpg
\015\012\015\012\015\012\015\012\015\012\015\012Fig. 4: Grasp the fuses with the puller and pull straight out to remove the fuses \015\01291146p68.jpg
\015\012\015\012\015\012\015\012\015\012\015\012Fig. 5: There are generally four types of fuses used in these vehicles \015\01288256g69.gif
\015\012\015\012\015\012\015\012\015\012\015\012Fig. 6: Fuse current rating and color code chart \015\01288256g70.gif
\015\012\015\012\015\012\015\012\015\012\015\012Fig. 7: Visual examination will reveal a blown fuse, but it should not be replaced until repairs are made \015\01287956094.gif
\015\012Fuses protect all the major electrical systems in the car. In case of an electrical overload, the fuse melts, breaking the circuit and stopping the flow of electricity. \015\012If a fuse blows, the cause should be investigated and corrected before the installation of a new fuse. This, however, is said than done. Because each fuse protects a limited number of components, your job is narrowed down somewhat. Begin your investigation by looking for obvious fraying, loose connections, breaks in insulation, etc. Use the techniques outlined at the beginning of this section. Electrical problems are almost always a real headache to solve, but if you are patient and persistent, and approach the problem logically (that is, don't start replacing electrical components randomly), you will eventually find the solution. \015\012Each fuse block uses miniature fuses (normally plug-in blade terminal-type for these vehicles) which are designed for increased circuit protection and greater reliability. The compact plug-in or blade terminal design allows for fingertip removal and replacement. \015\012Although most fuses are interchangeable in size, the amperage values are not. Should you install a fuse with too high a value, damaging current could be allowed to destroy the component you were attempting to protect by using a fuse in the first place. The plug-in type fuses have a volt number molded on them and are color coded for easy identification. Be sure to only replace a fuse with the proper amperage rated substitute. \015\012A blown fuse can easily be checked by visual inspection or by continuity checking. \015\012The fuse block is located on the lower left side of the instrument panel. To access the fuse panel, open the driver's side door. Pull off the fuse panel cover to get to the fuses. Spare fuses and a fuse puller should always be kept here. Various convenience connectors, which snap-lock into the fuse block, add to the serviceability of this unit. \015\012
    \015\012
  1. Locate the fuse for the circuit in question. \015\012NOTE: When replacing the fuse, always use a replacement fuse of the same amperage value. NEVER use one with a higher amperage rating. \015\012
    \015\012
  2. Check the fuse by pulling it from the fuse block and observing the element. If it is broken, install a replacement fuse the same amperage rating. If the fuse blows again, check the circuit for a short to ground or faulty device in the circuit protected by the fuse. \015\012
  3. Continuity can also be checked with the fuse installed in the fuse block with the use of a test light connected across the 2 test points on the end of the fuse. If the test light lights, replace the fuse. Check the circuit for a short to ground or faulty device in the circuit protected by the fuse.
\015\012\015\012prev.gif next.gif---\015\012Or, try to look for burnt out bulbs in instrument panel.
Repair Help & Product Troubleshooting for 1999 Chevrolet Malibu

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loading ...

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0080 seconds