Having problems with your Oldsmobile Bravada ?

Heater core is leaking all over carpet so how do i go about getting that dash out of my 96 olds bravada

Posted / edited by AnonymousUser on : 15-07-2019

Answers :

CAUTION\015\012\015\012\015\012When performing service around the air bag system components or\015\012wiring, the air bag system MUST be disabled. Failure to do so could\015\012result in possible air bag deployment, personal injury or unneeded air\015\012bag system repairs. \015\012\015\012
\015\012\015\012
    \015\012
  1. \015\012Disconnect the negative battery cable.\015\012
  2. \015\012
  3. \015\012\015\012 Disable the air bag system. Please refer to Supplemental Inflatable Restraint (SIR) System in\015\012 \015\012 .\015\012 \015\012
  4. \015\012
  5. \015\012Set the parking brake and block the wheels.\015\012
  6. \015\012
  7. \015\012Disconnect the parking brake release cable from the parking brake lever.\015\012
  8. \015\012
  9. \015\012Unfasten the screws that retain the Data Link Connector (DLC)\015\012instrument panel left side sound insulator. Feed the DLC through the\015\012hole in the sound insulator.\015\012
  10. \015\012
  11. \015\012Unfasten the right side sound insulator panel screws and remove the panel.\015\012
  12. \015\012
  13. \015\012Unfasten the screws that attach the instrument panel left side sound insulator to the knee bolster and cowl panel.\015\012
  14. \015\012
  15. \015\012Unfasten the nut that attaches the left side sound insulator to the accelerator pedal bracket.\015\012
  16. \015\012
  17. \015\012Unplug the remote control door lock receiver module electrical connector.\015\012
  18. \015\012
  19. \015\012Remove the door lock receiver module from the left side sound insulator. Remove the left side sound insulator.\015\012
  20. \015\012
  21. \015\012Unfasten the screws that attach the instrument panel center sound\015\012insulator to the knee bolster, instrument panel, heater assembly and\015\012floor duct.\015\012
  22. \015\012
  23. \015\012Remove the center sound insulator.\015\012
  24. \015\012
  25. \015\012Unfasten the screws that attach the courtesy lamp to the knee bolster.\015\012
  26. \015\012
  27. \015\012Unfasten the screws that attach the knee bolster to the instrument panel.\015\012
  28. \015\012
  29. \015\012Disconnect the lap cooler duct from the knee bolster.\015\012
  30. \015\012
  31. \015\012Unplug the lighter electrical connection and remove the knee bolster.\015\012
  32. \015\012
  33. \015\012Unfasten the steering column-to-instrument panel nuts and lower the column.\015\012
  34. \015\012
  35. \015\012Unfasten the screws that attach the instrument panel accessory trim plate to the instrument panel.\015\012
  36. \015\012
  37. \015\012Remove the trim plate and unplug all necessary electrical connection.\015\012
  38. \015\012
  39. \015\012Remove the heater and/or A/C control assembly.\015\012
  40. \015\012
  41. \015\012Remove the radio and the storage compartment assembly (if equipped).\015\012
  42. \015\012
  43. \015\012If necessary, remove the instrument cluster.\015\012
  44. \015\012
  45. \015\012Unfasten the left and right instrument panel pivot bolts and the panel lower support bolt.\015\012
  46. \015\012
  47. \015\012Unfasten the speaker grilles retaining screws and remove the speaker grilles.\015\012
  48. \015\012
  49. \015\012Remove the windshield defroster grille using a flat-bladed\015\012prytool. Start at one end of the grille and work your way down the\015\012grille.\015\012
  50. \015\012
  51. \015\012Unfasten the four instrument panel upper support screws.\015\012
  52. \015\012
  53. \015\012Tag and unplug all necessary electrical connections.\015\012
  54. \015\012
  55. \015\012Remove the instrument panel from the vehicle.\015\012
\015\012
\015\012To install:
\015\012
    \015\012
  1. \015\012Rest the instrument panel on the lower pivot studs.\015\012
  2. \015\012
  3. \015\012Attach the electrical connections.\015\012
  4. \015\012
  5. \015\012Install but do not tighten the four upper instrument panel support screws.\015\012
  6. \015\012
  7. \015\012Install the left and right panel pivot bolts. Tighten the bolts to 102 inch lbs. (11.5 Nm).\015\012
  8. \015\012
  9. \015\012Install the panel lower support bolt. Tighten the bolt to 102 inch lbs. (11.5 Nm).\015\012
  10. \015\012
  11. \015\012Tighten the upper support screws to 17 inch lbs. (1.9 Nm).\015\012
  12. \015\012
  13. \015\012Install the windshield defroster grille and the speaker grilles.\015\012
  14. \015\012
  15. \015\012Install the radio and storage compartment assembly (if equipped).\015\012
  16. \015\012
  17. \015\012If removed, install the instrument cluster.\015\012
  18. \015\012
  19. \015\012Install the heater and/or A/C control assembly.\015\012
  20. \015\012
  21. \015\012Attach the electrical connections to the instrument panel accessory trim plate.\015\012
  22. \015\012
  23. \015\012Place the trim plate in position and install its retaining screws. Tighten the screws to 17 inch lbs. (1.9 Nm).\015\012
  24. \015\012
  25. \015\012Place the steering column into position and install its retaining nuts. Tighten the nuts to 22 ft. lbs. (30 Nm).\015\012
  26. \015\012
  27. \015\012Attach the lighter electrical connection and the lap cooler duct to the knee bolster.\015\012
  28. \015\012
  29. \015\012Place the knee bolster into position and install its retaining\015\012screws. Tighten the Torx® head screws to 80 inch lbs. (9 Nm) and the\015\012hex head screws to 17 inch lbs. (1.9 Nm).\015\012
  30. \015\012
  31. \015\012Place the courtesy lamp in position and install its screws. Tighten the screws to 17 inch lbs. (1.9 Nm).\015\012
  32. \015\012
  33. \015\012Place the instrument panel center sound insulator in position.\015\012Install the screws that attach the center sound insulator to the knee\015\012bolster, instrument panel and the floor duct. Tighten the screws to 17\015\012inch lbs. (1.9 Nm).\015\012
  34. \015\012
  35. \015\012Install the screw that attaches the center sound insulator to the heater assembly. Tighten the screw to 13 inch lbs. (1.5 Nm).\015\012
  36. \015\012
  37. \015\012Install the remote control door lock receiver module to the instrument panel left side sound insulator.\015\012
  38. \015\012
  39. \015\012Attach the door lock receiver electrical connection.\015\012
  40. \015\012
  41. \015\012Install the nut that attaches the left side sound insulator to\015\012the accelerator pedal bracket. Tighten the nut to 35 inch lbs. (4 Nm).\015\012
  42. \015\012
  43. \015\012Install the screw that attaches the left side sound insulator to cowl panel. Tighten the screw to 13 inch lbs. (1.5 Nm).\015\012
  44. \015\012
  45. \015\012Install the screws that attach the left side sound insulator to knee bolster. Tighten the screw to 17 inch lbs. (1.9 Nm).\015\012
  46. \015\012
  47. \015\012Feed the DLC through the hole in the sound insulator, place the\015\012DLC in position and install its retaining screws. Tighten the screws to\015\01221 inch lbs. (2.4 Nm).\015\012
  48. \015\012
  49. \015\012Install the right side sound insulator and tighten the screws\015\012
  50. \015\012
  51. \015\012Connect the parking brake release cable to the lever.\015\012
  52. \015\012
  53. \015\012\015\012 Enable the air bag system. Please refer to\015\012 \015\012 .\015\012 \015\012
  54. \015\012
  55. \015\012Connect the negative battery cable.\015\012

Hope helped with this.
Repair Help & Product Troubleshooting for Oldsmobile Bravada

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loading ...

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0082 seconds